Book

The publisher is making a number of good points relating to How to Install a Bathtub Yourself overall in the article further down.

Setting up a bath tub isn't exactly rocket science, however it does call for strong plumbing, carpentry, and often, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably hard task. If the old bathtub is readily available, the project can move rapidly; if you need to open a wall to get rid of the old tub and position the new tub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly need a helper to vacate the old bathtub as well as set in the brand-new one. See to it you have actually qualified on your own for the task as well as are comfortable trying it. As opposed to employing a professional to take over a halfway-completed task, it is better to consider using one before you start. Opportunities are you may require a professional plumber to make tube links.
This short article will certainly help you mount a new tub in your restroom if you have actually already gotten a brand-new tub as well as do not need to alter the setup of your previous water system pipes.
Your tools as well as product checklist need to comprise the following:

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Measuring tape


• Pipeline Caps


 

Removing Old Touches

If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you should do is disconnect the water system. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of removing the existing faucets can be rather troublesome because of the limited access that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary taps from turning during this procedure. Once the faucets have been removed, the holes in the bath/basin will have to be cleansed of any kind of old sealing substance.
Before moving on to fit the brand-new faucets, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.

Fitting New Touches

If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and the other end provides a link to the current supply pipes.
If you need to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in area in between the tap and the sink. Protect the tap in position with the producer supplied backnut. As soon as the faucet is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap ports. The previous kind ought to be attached to the faucet finishes first, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.

Installing the Tub

Using both wood boards under its feet, place the bathtub in the required setting. The wood boards are valuable in evenly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four tiny factors.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the spirit level and changing the feet on the bath tub till the spirit level reviews degree.
To set up taps, fit the bottom of the furthest adaptable faucet adapter to the proper supply pipe by making a compression join; after that do the exact same for the other faucet.
Turn on the water as well as examine all joints and also new pipework for leakages as well as tighten them if needed. Load the bath tub as well as likewise examine the overflow outlet and also the normal electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the maker's instruction manual. Tiling and sealing around the bathtub ought to wait until the bathtub has actually been used at the very least once as this will settle it right into its last setting.

Getting ready for the Installation

Firstly, the supporting frame supplied with the bath ought to be fitted (if required) according to the manufacturer's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to see to it that if the tap comes with a plastic washer, it is fitted between the bath and also the taps. On a plastic bath, it is also practical to fit a supporting plate under the faucets device to avoid strain on the tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you make use of all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to now prepare to be suited its final placement.

Tiling Around the Bathtub

In the area where the bathroom fulfills the tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to crack a rigid seal, triggering the water to pass through the wall surface in between the bathroom and the tiling, leading to difficulties with wetness and possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and installations. They are marketed in tubes as well as cartridges, and also are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to allow for the activity experienced when the tub is in usage. The sealant can split relatively very early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise conveniently readily available on the marketplace. It is suggested to fit the floor tiles utilizing waterproof or waterproof sticky and cement.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

As an avid reader about How to Install a Bathtub Yourself, I figured sharing that portion was a good thing. If you please take the opportunity to distribute this blog if you enjoyed reading it. Thanks a lot for going through it.

Quick relief? Dial!